My Zigbee2MQTT is continuously restarting. I recently had to change the adapter from zstack to ember because of an update. I have a Sonoff stick E and updated to the latest firmware. This resulted in the following errors:
[2025-02-22 20:55:26] error: zh:ember:uart:ash: Received frame with CRC error
[2025-02-22 20:55:26] error: zh:ember:uart:ash: Received ERROR from adapter while connecting, with code=ERROR_EXCEEDED_MAXIMUM_ACK_TIMEOUT_COUNT.
So I read somewhere to add this to my config. yaml:
ota:
image_block_response_delay: 200
default_maximum_data_size: 15
That helped for a little while, but after a few days I had the same errors again. People advised to change the WiFi channel because it could be interference. So I did that and it worked, Zigbee2MQTT doesn’t fail anymore and I don’t get errors anymore, so far. But is it normal that Zigbee2MQTT restarts every hour or so?
[2025-02-26 11:43:00] info: zh:ember: [NCP COUNTERS] 2661,478,173,132,20,0,0,0,58,73,0,0,62,7,0,4,0,0,0,0,0,11,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
[2025-02-26 11:43:00] info: zh:ember: [ASH COUNTERS] 2265,404,108,295,0,0,0,0,5587,295,294,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
[2025-02-26 11:43:00] info: zh:ember: [ASH COUNTERS] 2265,404,108,295,0,0,0,0,5587,295,294,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
[11:49:33] INFO: Preparing to start...
[11:49:34] INFO: Socat not enabled
[11:49:35] INFO: Starting Zigbee2MQTT...
Starting Zigbee2MQTT without watchdog.
[2025-02-26 11:49:53] info: z2m: Logging to console, file (filename: log.log)
[2025-02-26 11:49:53] info: z2m: Starting Zigbee2MQTT version 2.1.1 (commit #unknown)
[2025-02-26 11:49:53] info: z2m: Starting zigbee-herdsman (3.2.5)
[2025-02-26 11:49:54] info: zh:ember: Using default stack config.
[2025-02-26 11:49:54] info: zh:ember: ======== Ember Adapter Starting ========
[2025-02-26 11:49:54] info: zh:ember:ezsp: ======== EZSP starting ========
[2025-02-26 11:49:54] info: zh:ember:uart:ash: ======== ASH Adapter reset ========
[2025-02-26 11:49:54] info: zh:ember:uart:ash: RTS/CTS config is off, enabling software flow control.
[2025-02-26 11:49:54] info: zh:ember:uart:ash: Serial port opened
[2025-02-26 11:49:54] info: zh:ember:uart:ash: ======== ASH starting ========
[2025-02-26 11:49:55] info: zh:ember:uart:ash: ======== ASH connected ========
[2025-02-26 11:49:55] info: zh:ember:uart:ash: ======== ASH started ========
[2025-02-26 11:49:55] info: zh:ember:ezsp: ======== EZSP started ========
[2025-02-26 11:49:55] info: zh:ember: Adapter EZSP protocol version (13) lower than Host. Switched.
[2025-02-26 11:49:55] info: zh:ember: Adapter version info: {"ezsp":13,"revision":"7.4.4 [GA]","build":0,"major":7,"minor":4,"patch":4,"special":0,"type":170}
[2025-02-26 11:49:55] info: zh:ember: [STACK STATUS] Network up.
[2025-02-26 11:49:55] info: zh:ember: [INIT TC] Adapter network matches config.
[2025-02-26 11:49:55] info: zh:ember: [CONCENTRATOR] Started source route discovery. 1248ms until next broadcast.
[2025-02-26 11:49:55] info: z2m: zigbee-herdsman started (resumed)
[2025-02-26 11:49:55] info: z2m: Coordinator firmware version: '{"meta":{"build":0,"ezsp":13,"major":7,"minor":4,"patch":4,"revision":"7.4.4 [GA]","special":0,"type":170},"type":"EmberZNet"}'
My config file looks like this now:
data_path: /config/zigbee2mqtt
socat:
enabled: false
master: pty,raw,echo=0,link=/tmp/ttyZ2M,mode=777
slave: tcp-listen:8485,keepalive,nodelay,reuseaddr,keepidle=1,keepintvl=1,keepcnt=5
options: "-d -d"
log: false
mqtt:
server: mqtt://core-mosquitto:1883
user: ***
password: ***
serial:
port: >-
/dev/serial/by-id/usb-ITEAD_SONOFF_Zigbee_3.0_USB_Dongle_Plus_V2_20240124210837-if00
adapter: ember
advanced:
homeassistant_legacy_entity_attributes: false
homeassistant_legacy_triggers: false
legacy_api: false
legacy_availability_payload: false
device_options:
legacy: false
ota:
image_block_response_delay: 200
default_maximum_data_size: 15
1 post - 1 participant