Walli Roller Shutter state / position not reported back in Home Assistant

@jenova70 wrote:

Hello guys,

I think my question is more a generic ZWave question since I am just starting but nevertheless I will explain you what I am experiencing !

I am available if you want logs for each use-cases I am describing below.

So the past two days I fiddled with ZWave to make my first Zwave “network” composed of two nodes

• (node 1) The Aeotec Z-Stick Gen5 (link)
• (node 4) A Fibaro Walli Roller Shutter (link)

I finally managed to reach a “usable” state, but I have issue of update / reporting…

With the physical button I can:

• Fully open the rolling shutter by clicking the up button
• Fully close the rolling shutter by clicking the down button
• If I click any button during a movement, I can also stop the rolling shutter at the current position

And in Home Assistant via the services I can:

• open fully via cover.open_cover
• close fully via cover.close_cover
• stop the movement via cover.stop_cover
• set the rolling shutter at a specific position via cover.set_cover_position

The issue :
Basically, only stopping the cover (Either via physical click or via cover.stop_cover) is updating the position / state back in home assistant…

• If I open / close fully the shutter (Physically or via home assistant service), the position / state is not updated …
• If I set a specific position via cover.set_cover_position, the position / state is not updated …

How can I debug this ?
Where do I start ?
I tried to read the OZW_log but I do not understand what is wrong…

Thank you in advance !
JLP

This are my OWZ_log when I click on TEST NETWORK in the configuration tab of hassio

2020-01-29 09:08:53.247 Info, Node004, NoOperation::Set - Routing=true
2020-01-29 09:08:53.247 Detail, Node004, Queuing (NoOp) NoOperation_Set (Node=4): 0x01, 0x09, 0x00, 0x13, 0x04, 0x02, 0x00, 0x00, 0x25, 0xb5, 0x73
2020-01-29 09:08:53.247 Detail, 
2020-01-29 09:08:53.248 Info, Node004, Sending (NoOp) message (Callback ID=0xb5, Expected Reply=0x13) - NoOperation_Set (Node=4): 0x01, 0x09, 0x00, 0x13, 0x04, 0x02, 0x00, 0x00, 0x25, 0xb5, 0x73
2020-01-29 09:08:53.258 Detail, Node004,   Received: 0x01, 0x04, 0x01, 0x13, 0x01, 0xe8
2020-01-29 09:08:53.259 Detail, Node004,   ZW_SEND_DATA delivered to Z-Wave stack
2020-01-29 09:08:53.272 Detail, Node004,   Received: 0x01, 0x07, 0x00, 0x13, 0xb5, 0x00, 0x00, 0x02, 0x5c
2020-01-29 09:08:53.273 Detail, Node004,   ZW_SEND_DATA Request with callback ID 0xb5 received (expected 0xb5)
2020-01-29 09:08:53.273 Info, Node004, Request RTT 24 Average Request RTT 57
2020-01-29 09:08:53.273 Detail,   Expected callbackId was received
2020-01-29 09:08:53.273 Detail,   Expected reply was received
2020-01-29 09:08:53.273 Detail,   Message transaction complete
2020-01-29 09:08:53.273 Detail, 
2020-01-29 09:08:53.273 Detail, Node004, Removing current message
2020-01-29 09:08:53.273 Detail, Node004, Notification: Notification - NoOperation

Posts: 1

Participants: 1

Read full topic