Re configure entire zwave network?
@tlf wrote: So I’ve been using HA since the 0.70’s and have had some Z Wave devices (Aeotec stuff) since then. Recently I’ve been adding some new devices and noticed that HA has quite a few outdated...
View ArticleClik here to view.
Lovelace Map Card Ignores Zones
@segfaultex wrote: As of v 0.105 The ability to keep zones shown in the Map Card has been removed. “ map card: Ignore zones when fitting map (#4447) @klejejs” How do I make the map zoom to always show...
View ArticleHow many of you using Home Assistant Cloud?
@mcnaveen wrote: I recently started using Home Assistant and to be honest I’m complete noob to these things. I’m good at programming. But not much into electronic hardware stuffs. This community is...
View ArticleTons of failures after 105.1 upgrade
@jspanitz wrote: Not sure what happened here but I now have an invalid configuration after the upgrade. Everything was good before the upgrade when I was on 104.x builds. In lovelace under...
View ArticleIs there a Media Player that reports the currently playing media title and app
@FunPsycho wrote: Just a quick question. Is there a device (Android TV, Fire Stick, Roku, etc.) that reports or can report to Home Assistant what is playing? So it would Say Netflix, The Walking Dead...
View ArticleClik here to view.
MQTT Garage door opener with 2 reed switches on a Wemos D1mini Pro
@Crumpy10 wrote: Hello Everyone, I need a little direction help please! I have a Wemos D1 mini Pro running Tasmota as a garage door opener, with 2 reed switches, one for open and the other for closed....
View ArticleCan I specify a part of a page to display in an iframe?
@Andarras wrote: Hi, I want to be able to specify a part of a webpage. Is this possible? I’ve found hte following code, but not sure if this works in Hass.IO or how to implement it: <div...
View ArticleGoogle assistant on Android suddenly requires unlock
@seanomat wrote: I upgraded my pixel 3a to the February patch. This might just be a coincidence, but since then I can no longer voice-controll lights and switches without unlocking the phone first. I...
View ArticleClik here to view.
Last_changed in lovelace, fix timezone
@dantist wrote: I have a markdown card in lovelace that shows when the front door was last opened, but it’s one hour off. content: >- {{...
View ArticleBitmanipulation for status and command via mqtt payload
@demeulemeesterdries wrote: Hi all I’m pretty new to Home assistant. The whole reason I tried to set it up is because I have rather dumb “domotics” light control system. It can only toggle output...
View ArticleClik here to view.
No "ignore" on Integrations for me
@Stooovie wrote: 0.104.2 and later are supposed to have an Ignore button next to Configure in Integrations. I did have it and used it for hiding Yeelights that were re-discovered on every boot but the...
View ArticleDevice Tracker, Geocoded location and Lovelace
@rafaborges wrote: Hi all, This should be simple, but I can’t find a solution. I used to have a device tracker showing which zone I was. After I went through a massive configuration change (new phone,...
View ArticleClik here to view.
Netatmo in HA 0.105
@h4nc wrote: @cgtobi for me the new configuration isn’t a 100% clear, maybe for others as well. So I changed my configuration as mentioned here: Home Assistant Netatmo Instructions on how to integrate...
View ArticleDid it freeze last night?
@SpacemanSpiff wrote: So, this morning I went to drive my kid to school. We were a bit late. When I stepped out the front door I saw that the windshield of my car had frozen over. So Home Assistant to...
View ArticleReceive sensor values from Home Assistant through Serial communication
@shazam96 wrote: Hi, I setup some sensors from NodeMCU with Home Assistant. I wrote a python script that gets gets the values from serial communication and through MQTT, publishes the values to Home...
View ArticleValue template to extract one attribute
@hajo62 wrote: I curl a public sensor resulting giving this result: { “timestamp”: “2020-02-06T12:15:00+01:00”, “value”: 799.0, “trend”: 1, “stateMnwMhw”: “normal”, “stateNswHsw”: “normal” } Now I...
View ArticleCC2531 no led: is it broken?
@bob8x wrote: Hello everyone! just a bit intro: I had my rpi2 with cc2531 and zigbee2mqtt up and running for one year, than 2-3 weeks ago some zbee devices were missing ( can’t recall if after a power...
View ArticleCall Google Home's "text to speak" service from a button card
@revolter wrote: I don’t find any media_player.speak_text service in the dropdown list. Posts: 6 Participants: 3 Read full topic
View ArticleHelp on how to write a trigger for PHYSICAL or LOGICAL status of Motion Sensor
@urbanscribe wrote: trying to tie motion sensors reported back from ELK M1 integration in order to trigger lights. only part i am not getting is how to monitor the PHYSICAL or LOGICAL state of the MS...
View ArticleHide_if_unavailable doesn't work?
@henry8866 wrote: I have below config for entities card, but hide_if_unavailable doesn’t work, what is the correct syntax? entities: - entity: binary_sensor.xx - entity: binary_sensor.xx - entity:...
View Article