Wled missing segment
So just set up wled with an led strip around the top of my son’s room. Works great. Now tried to use segment to do a reading light over his bed. Small White section controlled separately. I have...
View ArticleSimple configuration light on/off not working
Guys I m new and trying a few days to put a configuration for my outside light to go switch on and off on time. When test the config all work but the action has neven been triggered. need light on 45...
View ArticleOpenTherm software thermostat
OpenTherm Gateway - Home Assistant talks about an OpenTherm software thermostat. Is there any existing such software thermostat running on Home Assistant? 1 post - 1 participant Read full topic
View ArticleClik here to view.
Tasmota integration using device_name instead of friendly_name
Hello everyone, I have multiple Shelly 2.5 and as you know the monitor the power for both outputs. And both are shown separately in the WebUI. However, when using MQTT, despite setting two...
View ArticleZwave js, what means security unknown
I’m using Zwave-js with about 35 devices. Some are unsecured, some are s0-legacy secured (7x) (slow communication if i’m right informed) some are secured unknown (12x)? What does secured unknown...
View ArticleAmcrest Integration not showing in add integration list
Did the Amcrest integration get removed from HA. I’ve cleared my browser cache and I don’t see it when I click add integration. Not sure what I’m doing wrong 1 post - 1 participant Read full topic
View ArticleAutomation template using "For" time
Hi guys, I have a case with some motion sensors. The triggers are: a) when binary_sensor.motion_1_iaszone and binary_sensor.motion_2_iaszone changes to off b) when binary_sensor.motion_1_iaszone...
View ArticleMQTT switch and sensor dont work after 2022.9 upgrade
After I upgraded to 2022.9, I saw notification to change mqtt switch and sensor config. I followed up documentation examples, but after upgrade MQTT sensor and switches have stopped working After I’ve...
View ArticleCan't get node anchoring to work in template
I am trying to reuse some code in my template through a node anchor. I just don’t get it to work. This is the code: - sensor: - name: "NextHoliday" state: "OK" attributes: dummy: &order > {%...
View ArticleClik here to view.
Aqara temp/humidity sensor freeze
I have a lot of sensors, but this one freeze for days worked for over than a year with no problem - I have changed the battery and reset it and paired it agan (deconz) is it dead? i think if its dead...
View ArticleWhy is Tasmota only showing states on select devices?
Hello, I just noticed that Ha Tasmota is not showing me states like uptime on Shelly devices but it is on ESP32 dev kits. Why is that? Thank you Alex 1 post - 1 participant Read full topic
View ArticleAutomation that can change color of an LED strip to a few preset colors on...
I am using a SONOFF RM433R2 Remote Controller. I have already setup my SONOFF RF Bridge & I have paired all the buttons on my RM433R2 to my RF Bridge. I want to use one of the buttons on my...
View ArticleClik here to view.
Stuck getting Sonoff Zigbee 3 Dongle E working with zigbee2mqtt
Hello, complete HA n00b. I followed the following tutorial: Smart Home Junkie - Tutorials and Information for your Smart Home and Home... – 28 Aug 22 How to install Zigbee2MQTT with the Sonoff Zigbee...
View ArticleClik here to view.
How to control Shelly RGBW2 White Channel Brightness in Automation (Increase...
I wanted to control the brightness of my Shelly RGBW2 (Not connected via MQTT; using the Shelly Integration) White Channel using an Automation. But I am unable to do so. I went into Automation &...
View ArticleDifferences between switch platform state and switch on/off changes
Hi experts, I would like to know the fundamental differences between writing an trigger automation for a sonoff switch platform state OR a trigger for a switch turned on/off. Both the below works and...
View ArticleInput_text history listed in a lovelace card
Is there a card that can take a input_text history and LIST in lovelace? The history graph card is not ideal to show each change. input_text.notified_text 20:16 This happen 20:17 Then then that happen...
View ArticleEnergy dashboard results into lovelace card
Hello. In energy dashboard there is daily total energy in kWh and total daily costs in a preset currency. Is it possible to show those numbers somewhere elase in lovelace dashboard? Lets say on a...
View ArticleDaily energy meter results
Helly I have SHelly EM3 with FW 20220830-080542/v1.12-3EM-gcf4f7c2. Running Home Assistant 2022.9.1 Supervisor 2022.08.6 Operating System 8.5 Frontend 20220907.0 I have a problem. There are 3 sensors...
View ArticlePhilipps Hue Bluetooth link
Hi, I’m a small user of Home Assistant, I see now we have bluetooth integration. Can I link my bluetooth Hue Lamp without the hub ? I try to configure with no success… Thanks for your help. Joh 1 post...
View ArticleHow to set "state_class: total" correctly?
In order to use a statistic diagram to display rain sensor data in an hourly/daily manner it is needed to set state_class: total as described here I tried following configuration. But getting this...
View Article