Clik here to view.
Use conditional card to show different cards
I want to use the conditional card to display a different card depending on the condition. Let me explain. I use the shutter-card for my sunscreens. Which works fine. But i want to add conditions to...
View ArticleClik here to view.
Template sensor value to Dev Tools inconsistent
I have a template sensor which I use to obtain a list of select entities that match a specific state. template: - sensor: - name: "SHP Circuits Manual Mode" unique_id: shp_circuits_manual_mode icon:...
View ArticleDevice names shouldn't contain special charachters?
(feel free to move if not in right cat) Lots of integrations seem to add special characters like brackets in their device names. This is well and good EXCEPT for the fact that if you then try to...
View ArticleBTHome remote bluetooth
Hello, I’d like to use some BTHome protocol based sensors, but my HomeAssistant is running in docker on a machine without bluetooth. I have multiple Raspberry Pi-s in my home, and I’d like to use them...
View ArticleAutomation not firing when change the state
Hi Guys I have created a Automation that will Arm my Alarm system when I leave my Home Zone. When I physically leave home the Automation works, however if I change the STATE under the development...
View ArticleClik here to view.
Why did my automation stop running?
Hello, I have a doorbell automation which does some stuff, turns on porch light, and 1 minute later turns it off again. now here is the thing. it stopped running for some reason just before the 1...
View ArticleCannot connect (duckdns?)
I changed my router at home. After this i cannot connect to HA with duckdns. I port forwarded. It works with provider ip adres. So port forwarded works. I deleted duckdns. Added again. Not working....
View ArticleForecast in temperature
hello I’m looking for todays forecast in temperature. does anyone have any suggestions? I now use buienradar, but that only shows the forecast for tomorrow, the day after tomorrow, etc Thanks! 2 posts...
View ArticleSonoff T1 2CH - Dimmer switchmode not working?
(topic deleted by author) 1 post - 1 participant Read full topic
View ArticleNest thermostat hvac_action in Matter integration
I’m wondering if there’s a reason that the hvac_action attribute does not appear in my Nest thermostat climate entity in the Matter integration. All other attributes show up (cooling vs. heating mode,...
View ArticleExtract from IMAP sensor into calendar events
Hi All, For me an impossible job. Maybe can help me with this? Below you see a message that is added to a sensor by imap_content. Output of the sensor: Message: "Donderdagse Week van...
View ArticleCombine two media players on condition
Hi, I’m using the Sony Bravia TV integration which more or less does exactly what I need. The only exception being information about played media in apps, which only shows as “Smart TV”. According to...
View ArticleZHA Multiple Door Sensors stop working after a day
Hello, I’m looking for help troubleshooting ZHA/Skyconnect with Door Sensors. I have HAOS running on a RPi 4. I installed a SkyConnect (with extension) and I am using ZHA and I have 20 Zigbee devices...
View ArticleClik here to view.
Flux integration is not working properly anymore
Hi guys, my Flux platform broke few updates earlier and I have not found a way to fix it. The problem is that it does not change the color temp in steps but instantly from 4000 to 1900...
View ArticleNest Doorbell (Battery) + Frigate
Hello Everyone, I’m hoping there is many of you smarter than me that have figured this out. I have searched all over and have not found a reliable method to capture the new Nest Doorbell (Battery)...
View ArticleClik here to view.
Sonoff T1 2CH with D1 dimmer SwitchMode11 unknown command
Hello Im having trouble with the dimming part of my config. I have these two (dimmer and sonoff t1 2ch ) on a group and they share everything. If i use the below it works but the dimming is delayed....
View ArticleClik here to view.
MQTT sensor incorrect type error
Hi. I’ve just created an MQTT sensor in configuration.yaml by means: # Example configuration.yaml entry mqtt: - sensor: name: "PROVA" state_topic: "/test/topic" It works but, in the configuration.yaml...
View ArticleClik here to view.
Samsung smart TV integration should always be set up
Hi everyone Does anyone know why Samsung smart TV integration (in my case at least) keeps asking to be configured? Lately, in addition, I find myself repeating the integration, in the case below as...
View ArticleNeed help to change templates
Hello, I am currently in the process of cleaning up and optimizing my automations. Since I have taken a lot from the forum and I’m not exactly the professional for templates, I try to solve existing...
View ArticleHow to learn bluetooth commands - Universal Bluetooth Learner
Does anyone know a way to learn bluetooth commands? I’m just tired of having to get different hubs to connect to a specific device, in general, lights and controllers. So i’m trying to learn the...
View Article