How to use glances in HAOS
I tried on a i3, 8Gb to install HAOS. After some trial and error I managed to install a copy. But I saw I cannot ssh anymore into my host computer. ( The Terminal & SSH add-on does not provide...
View ArticleIntegrating Aqara M3 Hub and it's connected device into HA
Hi, I generally use Aqara devices as my IoT device choice for my house but recently I have been thinking of integrating it into HA. When I port over my Aqara M3 hub over to HA, only the sensors are...
View ArticleWhy Do These Two Cards Have Different "Hold" Behavior Even Though the Code...
(topic deleted by author) 1 post - 1 participant Read full topic
View ArticleClik here to view.
Help: Statistic Graph Card - Name
I nedd your help, because I didn’t see my mistake: What is wrong? 1 post - 1 participant Read full topic
View ArticleClik here to view.
How to Make 2 Triggers in Group for Light Automation Act in "and" Rather Than...
At least I think that’s what’s happening. My goal is to have my basement light turn on when presence is detected and then off again 2 minutes after presence is no longer detected. I have a Unifi...
View ArticleFirmware update of 4512737 by NAMRON A/S Floor heating thermostat
I have tried to update the firmware of my floor heating thermostat by Namron, model no 4512737. I’m on ZHA. I have DL:ed the latest FW from Koenkk Zigbee OTA, the correction provided stops the...
View ArticleMQTT value templates
My car returns a state of “heating”, “cooling” or “off” for climatisation, which I am trying to pull into a switch. However, it doesn’t seem to be working. I have: mqtt: switch: - name:...
View ArticleTuya Zigbee Smoke Detector not working with SkyConnect ZBT-1 dongle
I bought the Zigbee version of Tuya Smart Smoke Detector https://a.aliexpress.com/_EGFt3aK. I just started integrating my first Zigbee devices, so far I have done WiFi devices only instead. I bought a...
View ArticleWhich entity stores the net grid consumption?
So I am using an Iammeter module to monitor my grid. It provides me two sensors which I have configured in the Energy dashboard: sensor.imeter_xxxxxxxx_importenergy_x...
View ArticlePhilips Hue Motion Sensor battery always 100%
For my Philips Hue Motion Sensors, everything works, and even the battery level displays, but for all of mine, it shows 100% and never goes down. One day, the device suddenly disappears and becomes...
View ArticleAbout to dive into HA - Trying to understand Alarm.Com 7 QOLSys integrations
As the title says, I’m about to dive into the wonderful world of HA, but I’m trying to figure out how I can leverage some devices currently attached to my alarm panel. I’ll to try to keep the...
View ArticleZ-Wave Device Shows No Zwave Plus
I have 60 Zwave devices on my network with a Gen 5 Zstick. All are S2 authenticated with a mix of GE/Honeywell switches and outlets slowly being replaced with Zooz and Inovelli, a few Eaton outlets,...
View ArticleClik here to view.
Smoke alarm notification only appears after unlocking the screen
Dear Home Assistant fans, I have a quick question I hope someone can help me with. I’ve recently purchased a Zigbee Frient Smoke/Heat Detector and am currently setting up an automation for it....
View ArticleAfter restoring a backup, Home Assistant isn't coming back up
I’m using a Home Assistant Yellow, with an HAOS install. I accidentally removed my Matter configuration (long story – trying to get a device connected again) and lost all of my carefully curated...
View ArticleAlexa actionable notifications (VOICE ID)
Hi there. Im just wondering if its possible to configure alexa voice ID with actionable notifications? Example: The notification asks if you would like to disarm the alarm? Then you say a code or...
View ArticleNewbie: Energy von incomming and outgoing at EM24 CarloGavazzi
Hi, i am abslote new with HA. I have successfull installed HACS and also included my EM24 (Carlo Gavazzi energy meter) with https://verkoyen.eu/2025/05/carlo-gavazzi-em24-in-home-assistant-via-modbus/...
View ArticleDevice replacement without losing history
Hello everyone. I have Home Assistant Core with the default SQLite DB ed zigbee2mqtt on Docker. A Zigbee MMQ temperature sensor is broken and I would like to replace it. I would like to “hook” the...
View ArticleData['triggers'] not allowed. Why?
I am using literally the official sample https://docs.pi-hole.net/guides/misc/homeassistant/ but HA throws error on validation of automation data[‘triggers’] not allowed. Why? 9 posts - 3 participants...
View ArticleClik here to view.
Energy dashboard showing of the chart values
Usualy energy dashboard works correct, but on some day’s I receive unrealistically high values from the solar panels. The sensors themselves are OK but the dashboard is way off. I thought it was a...
View ArticleClik here to view.
Gemini with Voice PE
When I saw Voice PE on YouTube, I quickly ordered one. AmeriDroid had the better shipping price, and soon, I had my new Voice PE. The hardware setup was straightforward, and a pair of PC speakers...
View Article
