Clik here to view.
Newbee question templating: dealing with attributes
@Djiest wrote: I’m a newbee with templating and need some help to grasp the basic concepts. I have a couple of sensors, as follows When I test a template and loop over these sensors, some have the...
View ArticleFibaro FGMS001 duplicated messages
@xp1ratex wrote: Hi. I get duplicated messages from my motionsensor in OZW log, any idea whats causing this? I have no problem with my other fgms001. Running Hassio 0.103.5 in ubuntu 18.10 docker,...
View ArticleClik here to view.
Hass.io cannot use local DNS names in place of IP addresses in...
@SpikeyGG wrote: I searched through the forum and found this post which sounds very similar to mine but it seems to be specific to the philips hue. I am re-configuring my network trying to be as...
View ArticleClik here to view.
Home Assistant Alexa Cloud - Device is unresponsive
@Nimesh_Panchal wrote: Hello, I’ve signed up for HA Cloud to link to my Alexa devices for voice control. Everything seems to be connected correctly, however Alexa won’t control any devices? If I ask...
View ArticleAutomation Config - Updating entity based on MQTT topic
@rdlaner wrote: Hey folks, I’m trying to set up an automation that is triggered by an MQTT topic and then sets the value of an input number slider based on data from the MQTT topic. The trigger seems...
View ArticleKNX - Home Assistant Switch Toggle
@Gladz0r wrote: Hello there, I want to use a button on my KNX installation switch.alarm_knop to trigger an Home Assistant automation (automation.alarm_niemand_thuis - that is my alarm with connected...
View ArticleHow to create one button to switch all lights off on bottom floor
@sretlow wrote: I’ve been trying to make a group and other possible solutions which I’ve fou d on YouTube and here. Not succeeded. What I want is to create one button to switch All lights of when I go...
View ArticleClik here to view.
Deleted a complex Lovelace card by mistake :-(
@SylvainGa wrote: I’m using hass.io and do have a full backup from earlier today (through hass.io snapshot). Is there a way to get the card back? I really don’t want to sets all the entities again...
View ArticleClik here to view.
Unable to link Home Assistant to Google Assistant
@chanrwm wrote: Hi, New to Home Assistant and am trying to get Google Assistant hooked up. I followed the steps at: Home Assistant Google Assistant Setup for Google Assistant integration I set my home...
View ArticleAlexa_media erroring
@jriker1 wrote: Just updated the alexa_media component. I’m continuously getting the below for each of my devices: 2020-01-01 16:27:26 ERROR (MainThread) [homeassistant.helpers.entity] Update for...
View ArticleClik here to view.
Picture-element image not positioning correctly
@HipsterDufus wrote: After spending way too much time building a floorplan dashboard, I think I have something that I’m reasonably happy with. But have run into a problem that I can’t figure out. My...
View ArticleClik here to view.
Dyson switch - Turned on, auto mode & speed selection
@DrSpaldo wrote: Recently @tom_l helped me in writing a switch for my Dyson fan. I have created a new topic as it is going down another path. The switch he created was as follows: switch: - platform:...
View ArticleHow to get the state of a switch updated from 2 different mqtt messages?
@mikep wrote: I’m using tasmota with hassio. I have a switch and I get state of the switch on or off from 2 different mqtt messages and I was wondering how to update the switch state correctly. 1 of...
View ArticleValue_template used truncate, but want type 'slice'
@TheStigh wrote: Hi, I have a sensor today where I get a long value in return. I’ve used truncate earlier that works fine, but it takes the first X letters of the value. Now I want to grab some text...
View ArticleUse MQTT retained value as condition?
@halest wrote: Hey, Google wasn’t too helpful, so here’s my question for all of you lovely folks. As far as I see it right now it is not possible in an automation condition to ask for an MQTT state,...
View ArticleClik here to view.
Why is Updater unavailable?
@ihavenoidea wrote: Just installed Hass.io on a new Pi4. I’ve noticed the Updater icon at the top is Unavailable. I’m new to HA so I’m not sure if this is expected or not. Posts: 2 Participants: 2...
View ArticleAutomation with Philips Hue and transition issue
@TheStigh wrote: Hi all, I use an automation to light up a Philips Hue bulb at night based on motion. I use transition to dim the light when it goes off, and all works fine. But when we wake up in the...
View ArticleKNX warnings
@Carlos_Lara wrote: Hi, I am having the following warnings in my logs: 2020-01-02 03:28:22 WARNING (MainThread) [homeassistant.loader] You are using a custom integration for circadian_lighting which...
View ArticleAutomation to switch ecobee to "heating" when another ecobee turns to heating
@Meeseeks wrote: The house I bought ended up having a boiler that’s way oversized for the three separate zones that they put in, so it short cycles a lot. To try and avoid that a little bit at least,...
View ArticleHow to retrieve the network key
@tshin wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View Article