Problem connecting to Homematic Hmip-BRC2 Switch
@topse wrote: Hi, I am trying to connect to a HMIP-BRC2-Switch from Homematic. The pymatic-Library seems to support it. The CCU2, which was installed as Container in Hassio, has recognized the Switch...
View ArticleConfiguration with Denon AVR 2113 (automation & script maybe)
@mcpaha wrote: Hi! I have denon avr-2113 which is now visible at HA. media_player: - platform: denonavr host: 192.168.1.111 name: Denon show_all_sources: true timeout: 2 zones: - zone: Zone2 name:...
View ArticleMore intervals in Gauge
@rajan wrote: I have a Gauge card: entity: sensor.temperature_14 max: 40 min: -15 name: Ute severity: green: 0 red: 25 yellow: 15 theme: Dark-Gray type: gauge But like to add more temperature...
View ArticleClik here to view.
Partial Switch to Light
@DemonAngel44 wrote: I have a number of Sonoff T0 US 3 Channel switches installed across the hours that is running Tasmota 8.3.1. A few of these channels are not actually connected to any lights...
View ArticleSelect panel based on room presence / internal positioning
@sebakerckhof wrote: Hi, I have a dashboard for each of my rooms, which only shows the stuff relevant for that room. I also have FIND setup which tracks my position inside the house. What I would like...
View ArticleClik here to view.
Influxdb: write to db only every
@prankousky wrote: Hi everybody, I used to have influxdb set up like this influxdb: host: !secret influxdb_host port: !secret influxdb_host database: !secret influxdb_database username: !secret...
View ArticleNo way to install tensorflow into homeassistant on raspberry pi 4
@Petengy wrote: Following the official guide it was not possible (to me) to install tensorflow in home assistant. Here my system conf: Raspberry pi 4 model B – 4GB RAM – CPU Cortex A-72 – Architecture...
View ArticleClik here to view.
DIYRuZRT Zigbee 3.0 firmware with external sensor support for Sonoff BASICZBR3
@Hedda wrote: Ilya Kirov (kirovilya on GitHub) has released source code for building Z-Stack 3.0 Zigbee 3.0 firmware for Texas Instruments CC2530 based devices with support for a single relay and...
View ArticleHuawei LTE integration is filling up DB
@drogfild wrote: I was checking what has caused my DB to grow and ran queries to DB with SQLite Web addon. I ran following query to find out that top 13 of my all entries in states -table are from...
View ArticleExclude_Entities
@Wes93 wrote: Hello to everyone: I need some help, i use this integration https://www.home-assistant.io/integrations/homekit/ and i want to exclude a series of entity that are called...
View ArticleWill this inexpensive RPI_AC108 Audio Board / HAT with a 4-Mic Array for...
@Hedda wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleSNMP disk information from Synology NAS
@jeppper wrote: Has someone tried to get disk information like status, size etc for a Synology NAS with SEVERAL disks? I have found the MIB with OIDs but I can´t figure out how to somehow parse...
View ArticleLovelace unusable following change to entities, help me recover?
@msambol wrote: I’ve had a long-stable HA 0.92.2 as the platform for my home automation and alarm, using Konnected. Recently I discovered a problem with konnected, and had to change the wiring between...
View ArticleDVR Stream OK but how do I get a capture image
@dicko wrote: Hi I have had the stream working for a while now but never tested the capture but now I am hoping to use the capture image. I have a DVR and the cameras are NOT IP cameras. So whats the...
View ArticlePWM for Cpu fans
@karansoi wrote: I have pwmled working with pigpio as an automation to run the twin cooling fans on my armour case. This is my automation - id: Update Cpu Temperature alias: Time to Start Cpu Cooling...
View ArticleRpi4 with Aeotec zwave - device name change without power cycle
@ecologicalSlinky wrote: I’m new to HA and still learning. I have the Aeotec Z-Stick Gen5 with a raspberry pi 4 (connected to a 4 port USB 2 Sabrent hub). I have setup a single switch from my prior...
View ArticleDefault values for script parameters?
@quentinsf wrote: I’m delighted to see that scripts can take parameters using the ‘fields’ clause. Each parameter can be given a description and an example value. It would be very nice to set defaults...
View ArticleConditional execution of individual items in a script?
@quentinsf wrote: In scripts, you can add tests for conditions. If the condition fails, the script stops. But I think that’s the only kind of condition test allowed? I was wondering how easy it would...
View ArticleIron icon height / width not working anymore
@MarvinE wrote: Hi all, I have some picture elements cards that show an overview of my home (downstairs, upstairs) which shows the lights, temp and who’s home or not. For example the following piece...
View ArticleClik here to view.
Mounting USB drive in HassOS for Plex media server
@Konrad162 wrote: Hello, I saw a lot of topics but none of them was very up to date and didn’t fully explain if this is possible or not. And if it is possible then how to do it. I have Plex media...
View Article