Automation to delete files from folder older than x days
@majkers wrote: Hello, I would like HA to record short video files when motion in my camera is detected. They will be stored somewhere in www folder let’s say www/camera_motion. I would like to...
View ArticleFibaro HC3 integration
@pitp2 wrote: Hi, I use the Fibaro integration with an HC2 without any problem and thank you for this great integration. Now I use the new HC3 from Fibaro but the integration doesn’t work anymore. If...
View ArticleSetup PIR sensor to Home Assistant (MQTT)
@amurka wrote: Help connect the PIR sensor to Home assistant. There is esp12 with tasmota firmware. The PIR sensor is connected to the esp12 pin, in the tasmota settings it is defined as a “switch”. A...
View ArticleInital WLED questions (NodeMCU)
@c0revin wrote: Hi guys, just flashed a NodeMCU 3 with WLED 0.10.0 (firmware image for 4MB flash) and got it talking to MQTT. It seems to be publishing the “old school” topics as “g”, “c”, “v”,...
View ArticleClik here to view.
HACS at the bottom of all pages
@AlJBrough wrote: Hi All, I updated to Home Assistant 0.110.3 today and now I have HACS fill the bottom of my browser 2020-05-28 19_08_14-Overview - Home Assistant1358×720 34.9 KB Any ideas on how to...
View ArticleClik here to view.
Node-RED Function to get multiple arrays
@jimpower wrote: I have a Node-RED flow that uses an API request for my cycle routes. It returns a huge array up to 2000 points each for elevation, speed & grade. I would like to pull these values...
View ArticleFilling sensor from command line with multiple outputs
@jaymu wrote: Hi everyone, I’m trying to fill two sensors for reading the ink levels of my printer. I have a command I can run on a remote IP address. By using remote ssh, it’s possible to run this on...
View ArticleHA is very unstable
@oliwa wrote: I have been using HA on a Raspberry Pi for close to two years. It was solid as a rock for about 6 months where it turns out my memory card died. Ok, bought a new card, restored snapshot...
View ArticleClik here to view.
Updating to 110 and the Config Check add-on
@klogg wrote: UPDATE BEFORE POSTING: I ran Config Check again and it went to the end (with no error found! - yay!) but the below comments about the version discrepancy and spelling mistakes are still...
View ArticleHow to control volume on Windows machine from Home Assistant?
@bessarabov wrote: I need to control system volume on Windows computer. I have tried several things but nothing works. IOTLink this software is working on windows machine. It sends data to mqtt server...
View ArticleSonoff bridge with Tasmota how to use a fob
@samtwilliams wrote: Hi All, I have a few 433 fobs that I want to use to control things on home assistant via 433 to my bridge. The issue I have is that the fobs learn codes by duplicating via...
View ArticleHooked up Open Zwave - Lost Nearly all Functionality
@bigverm23 wrote: Ok so I configured the new openzwave integration, which was seemingly easy enough. But didnt realize I was basically going to lose full configuration control over my devices....
View ArticleModbus and slave connections
@ZkiiFreak wrote: Hi I’ve got a TCP Modbus sensor configured which goes to my ventilation system. The integration works fine at start up of HA. After a while it starts throwing warnings “Updating...
View ArticleMQTT Devices Double Named
@JamesDenby wrote: I have recently noticed that all my MQTT switches (Sonoff S31 with Tasmota) now have double names. For example, within Lovelace a switch was named Guest_1. After the 110 upgrade the...
View ArticleHelp requested Life360 device conflict
@twofieros wrote: I’m new to home assistant. I’ve done a fresh install added all my devices, mobile app, etc. When I install life360 I get a uniqueID error will all the phones. I’ve deleted the home...
View ArticleClik here to view.
Zigbee2Mqtt - Ikea blinds
@Josh_Bruce wrote: Afternoon all. Sorry I know this probably isn’t the right forum for this post, but thought someone on here may know the answer. I am trying to pair my Ikea smart blinds to a Zigbee...
View ArticleAutomation: Checking the temperature at one hour and sending a telegram msg
@malpaso68 wrote: Hello, Can you help me? I am doing something wrong. I try to check the temperature (sensor aqara) at one hour, and if the result is less than 20 degrees, it should send a msg...
View ArticleChange group assignment deconz
@andyjacobs wrote: I’ve got an outlet that I’d like to move from one group to another in deConz but I can’t work out how to do it. Is it possible or am I going to have to remove it and re-add it?...
View ArticleClik here to view.
ESPHome sensors and misbehaving battery level icons
@klogg wrote: I have an ESPHome sensor set exactly as the docs show in the picture at the bottom of this post but my icon does not represent the battery level. I have tried customize homeassistant:...
View ArticleCommand line JSON to sensor
@larskuffer wrote: Hi, so I’m trying to add several sensors that I’m pulling out with a command. so far I’m trying to add a sensor in the configuration.yaml file like this: sensor: - platform:...
View Article