Clik here to view.
Mitsubishi Melcloud not sending data to HA
Hi there, I had integrated the Mitsubishi Melcloud, but since some time when I use the remote control to control my airco units, I see the Melcloud is showing right information (so on the Mitsubishi...
View ArticleWeather value only if greater than zero
Hi, I created the template sensor - trigger: - platform: time_pattern hours: /1 action: - service: weather.get_forecasts data: type: hourly target: entity_id: weather.openweathermap response_variable:...
View ArticleMqtt package synology and HA in docker no connection possible
Hi there, had to install my HA again and just used a backup-file. Nevertheless I am stuck with MQTT, I am not able to get it connected to HA in docker. I installed the MQTT package on my synology,...
View ArticleSeat occupancy sensor is too sensitive. How to output the average of a binary...
Hi everyone I’m a Home Assistant newb, so any help, guide, or key words to search would be greatly appreciated. I’ve attached an Aqara window sensor to a car seat sensor to use as a seat occupancy...
View ArticleTried and failed multiple attempts at room detection for just ONE device
I have a Olimex ESP32 POE board and tried to use it as a Bluetooth Proxy and as a ESPresense device that is located in the living room and all I want is for it to be able to trigger an automation when...
View ArticleMeross Smart Garage door opener to replace myQ
I will remove myQ from my network pretty soon. I have configured the Meross smart garage door opener in Home Assistant as a HomKit Device. I am just waiting for the additional device that will enable...
View ArticleEcobee smart thermostat enhanced
I am two weeks with the ecobee thermostat which I integrate with HA via the HomeKit Device integration. It replaced a Nest learning thermostat which I loved dearly before Google wants me to migrate...
View ArticleDisabling the cloud component
Hi, is core/homeassistant/components/default_config/manifest.json at cd8dac65b39c71b63495a385c4e36ff9b1e45ae3 · home-assistant/core · GitHub the same as default_config: ? I pasted this instead of...
View ArticleZ-Wave help/advice needed
I began building out my HA system in the last year. I chose Z-Wave as the protocol of choice partly because I already had a couple of devices from a previous system but also because Z-Wave appeared to...
View ArticleRest API Call - get all element from a dynamic array
Hi, i d like to get all “warning” inside “warnings” one sensor per “warning” - the problem I have that this could be 1…n. At the moment I address them static which can result in an error if there are...
View ArticleOSRAM 4052899926110 only update but no light entity after zigbee2mqtt update
After an update of zigbee2mqtt, 2 of my OSRAM light strips are no longer available as light entities, only the update entity is still available. The following error message also appears: Error 'some...
View ArticleIntegrate dehumifier to HA
I configurated a new dehumifier through Smart Life App and I can control it (setting the desired umidity level etc.) Is there a way to integrate that into HA? I looked for some custom component but...
View ArticleClik here to view.
Combining auto-entities & multiple-entity-row
Been fighting with this for a minute, bad not making progress… I’d like to us ‘auto-entites’ and their filters to supply the entities for ‘multiple-entity-row’. Can’t seem to get the syntax right....
View ArticleNeed help with light automation
Hi everyone Please help me with automation Description : Lights turn on manually by switch and should be turned off considering all this conditions: lights turned on for 5 minutes No motion detected...
View ArticleClik here to view.
Zigbee Energy Scan
I often read about performing an energy scan to see what zigbee channel to use if experiencing interference or high channel usage. However I am wondering what is the best way to perform the scan and...
View ArticleCombining multiple condition checks and set dynamic values accordingly
Hello, I have added several Sonoff Zigbee door sensors for alarms when absent. For this I added a helper “AlarmArmed” that can be on or off. When it is on and a door is opened it fires several alerts,...
View ArticlePhoscon Hive no Battery Status
I have 4 Phoscon Hive Battery lights on my Zigbee ZHA network. While I can control the lights without any issues and the devices are running the latest firmware, the battery status does not display....
View ArticleFibaro button automation
I was looking for a simple way to use a single push of the Fibaro Button to toggle a light. A lot of examples I found were very flexible in the use of the button but complicated. After adding the...
View ArticleClik here to view.
Adding Dyson Pure Humidify+Cool controls to the dashboard
Hi. I did add Dyson device, it’s fully controlable. But for some reason I can’t add some of the controls, like night mode to the overview dashboard. It seems I am lacking some kind of config? What I...
View ArticleClik here to view.
Help me solve my alignment
I have a question about the alignment. I’ve tried everything, but I can’t get this card right. I’m also sharing my code. As you can see, it should be the same as the other cards (right side) - type:...
View Article