Replacing CC2531 with antenna one
@vpomax wrote: Some months ago I have eliminated the Xiaomi Gateway replacing it with CC2531 and zigbee2mqtt. Considering that some sensors are at the limit of the signal range I tried to add a CC2531...
View ArticleClik here to view.
My powermeasurement setup doesn't work
@fribse wrote: Hi All I’ve gotten all my sensors to show some sort of daily usage. I’ve created a sensor to hold yesterdays usage: input_number: yesterday_powerusage: name: Samlet forbrug for i går...
View ArticleTwilio - Events from call notifications
@scorpio862 wrote: I’m trying to make a Call Notifications using Twilio for urgent security events like Fire Alarms. I managed to set up this notifications and Home Assistant calls my mobile phone...
View ArticleHow To Save Sensor Data To MySQL Database?
@AaronCake wrote: I have several sensors receiving data from an energy monitor that I would like to record in a more efficient and permanent format than the HA database. Primarily because the HA...
View ArticleESP8266 Hassio Light MQTT Auto Discovery not working
@nehulagr wrote: Hello, I am trying to configure a MQTT message from my ESP8266 where I am sending a Configuration payload as below { "name":"Dimmer Switch", "cmd_t":"myhome/light/dimmer/switch1/set",...
View ArticleDefault state for RGB lights (lifx)
@Woutch wrote: Dear all, I have 20 lifx lights in my living/dining room on different circuits. Those circuits have still there original light buttons, but i have added a shelly device behind them so...
View ArticleInovelli LZW31 seems to be reporting wrong power
@AlfaElan wrote: I installed an Inovelli LZW31 dimmer switch over the weekend and after going through updating the Open Z-Wave configuration it is working. But when I turn on my fixture with three 8...
View Article2 home assitant instances behind a reverse proxy
@l3x wrote: Hi, I hope Ive posted this in the correct location, it seemed the most relevant place. As the title suggests I have 2 home assistant instances running in 2 different locations. Both these...
View ArticleSensor unit of measurement not changing
@brucehvn wrote: Running hass.io 0.103.6. I ran into this issue when creating a template sensor to get the current temperature from my nest thermostat. I made a mistake specifying the unit of...
View ArticleZHA Lights: Enable Smooth transition?
@SimplyGardner wrote: Currently using some hue bulbs with ZHA. Everything is working brilliantly. When I manually change the brightness or colour of the bulbs, it instantly flips to the new setting...
View ArticleMultiple MQTT lights with one json command:
@yves1 wrote: I’m a new HASS user. I have 3 lights: store, room, kitchen. I’m only sending brightness values My set up is: Node-Red MQTT Modbus-TCP. Using Node-red, I can send inject a json:...
View ArticleControlling UI
@TQM wrote: I created some persons, I assigned devices to them - how do I get the list of persons that are in the network ? I see various devices that belong to person being in and out. How do I...
View ArticleSetting dim automation/scene/script with Leviton switches
@jjudson wrote: I’m a bit confused here (normal)… I have Leviton Z-Wave smart dimmers throughout the house and I’d like to try to set some automation using dim levels. I tried at first to setup a...
View ArticleClik here to view.
Docker permissions
@edtwodth wrote: Hi, I just installed home assistant in docker on raspberry pi as described here Home Assistant Installation on Docker Instructions to install Home Assistant on a Docker. docker run...
View ArticleCondition Using Sunrise / Sunset
@daave wrote: I copied this example directly form the documentation… condition: condition: and # 'when light' condition: before sunset and after sunrise - equivalent to a state condition on `sun.sun`...
View ArticleHow add a device to an area?
@Josep wrote: By example, a light to a room…I read I must go to integrations UI, and then in configured integrations -> devices, should be any way to add it to a configurated area… but I can’t find...
View ArticleBest way to structure similar automations
@belgian_style wrote: I currently have my automations structured in a way where each automation has a specific trigger and a specific action. For example, I have one automation for the single down...
View ArticleMedia_player media_title change
@Hiller131 wrote: I’m sure what I want to do is super simple but I’m driving myself crazy as a new user. In a nutshell I would like to be able to send out a serial command once the song title on my...
View ArticleUnable to make custom cards work
@nocd wrote: Unfortunately, I’ve been through all the threads and this is just driving me nuts. I’ve begun working on a custom UI for my HASS install (Unraid -> Docker -> hass v0.103.2). I...
View ArticleiOS Geocoding works - now what? (Time to home?)
@Ambidexter wrote: Hi Folks, I’ve starting using the ios integration, and it seems to be working fine. Thanks! I’ve noticed that the sensor.geocoded_location_X shows an address, lat/long, country,...
View Article