Clik here to view.
Entire dummy instance?
@prankousky wrote: Hi everybody, I could have sworn that there was a plugin for this in HACS, but I cannot find it any longer… but I’m sure somebody here will know what to do I have a working Home...
View ArticleClik here to view.
How do I correctly write a sensor value using the modbus.write_register()...
@bluebag wrote: I am trying to use the modbus.write_register() service to write the value of a sensor to a holding register. I am getting an error that the value I am seeking to pass is not an...
View ArticleInput_text in script
@Mati24 wrote: Hello I try to use input_text as script variable, but I get this error: 2020-04-18 10:56:24 ERROR (MainThread) [homeassistant.components.automation] Script_Name: Error executing script....
View ArticleZHA loses Aqara sensors after power outage
@Fronobulax wrote: Every time the power goes out long enough for the UPS to run dry and Home Assistant to shut down the following events occur. When everything comes back up all the Aqara sensors will...
View ArticleXiaomi Aqara Door and Window Sensor update interval problem
@Ronnie_Bilz wrote: Hey everyone, I have a problem with the update interval of my Aqara Door and Window Sensor. Because of my ZHWG11LM Hub i had to use the homekit integration mentiened by @Olivier974...
View ArticleClik here to view.
Z-Wave nodes dissapear if Z-Wave entities are modified
@Vlayke wrote: Hi, First of all, I’m relatively new to the Home Assistant. But I think this behavior is at least unusual, if not buggy… Of course, I might be wrong My config: Raspberry Pi 3B HassOS...
View ArticleOptimize automation for timer in Home Assistant
@cmartens wrote: Hi, I have created the following automation to set up a timer for my irrigation system. Based on a input_select, you can select one option and the time remaining is displayed in the...
View ArticleClik here to view.
Found an incorrect translation, but where to edit it on github?
@Mariusthvdb wrote: using Openweather Map is currently showing: Schermafbeelding 2020-04-18 om 13.10.04838×246 9.77 KB which is a contradiction in terms… should probably be either ‘lichte motregen’ as...
View ArticleClik here to view.
Legrand switch only showing battery status
@Jmi wrote: Hello, I’ve integrated Legrand switches (067723) and I they provide only battery status. I’ve tried with both zha/zigate and with a combee 2. When I push on/off buttons messages are seen,...
View ArticleCondition and value template error
@RGN01 wrote: I’m tearing my hair out - there is an error in this automation condition and I can’t figure out what it is! If I comment it out then the automation runs, as it does if I manually trigger...
View ArticleRemote ssh command: error 255
@Stooovie wrote: Hi, I see I’m not alone with SSH commands not working from HA GUI but I also don’t see a working solution. Goal is to set an automation to reboot an ASUS router in the morning....
View ArticleHelp identifying a package error, here's the log
@ninjadog wrote: I’ve copied and installed a package setup from a colleague. But, there’s error(s) and I’m not sure where ? Can you see - it’s something to do with “@ data[‘switch’][‘platform’]” but...
View ArticleShelly EM relay control
@richard-g8jvm wrote: Trying to use the relay control on a Shelly EM I can control the relay from mqtt explorer, but not from the lovelace >developer tools>mqtt mqtt explorer is ok with...
View ArticleGeneric IP camera and preload_stream flag
@HeyImAlex wrote: Hi all Is there a way to set the preload_stream flag for individual cameras using the generic IP camera platform ? I have several HikVisions using the generic platform with the...
View ArticleRFLink Somfy cover moves only a bit
@dseidl wrote: Dear Community, i managed to get the RFLINK Gateway from nodo to work. so i successfully connected all my covers with RFlinkLoader and configured the covers as follows: cover: -...
View Article2 Samsung tv one config
@VanQ wrote: How do i have a config for 2 samsung TV? my current config: wake_on_lan: # enables ‘wake_on_lan’ domain #Living Room samsungtv: host: 192.168.1.150 name: Samsung TV Tizen 55"...
View ArticleMedia_player.play_media Kodi Erroring
@Morphy wrote: Hi I had a script that was working fine some time ago and I’ve just got around to looking at automating it again and it seems it’s stopped working. The script was to play a rtsp stream...
View ArticleDifference between two values
@pitp2 wrote: Hi, I would like to subtract two values. The first value should be the value of a sensor at 20:00 and the second one the value at 09:00. The subtraction will be calculated at 20:00. The...
View ArticleClik here to view.
Pollen Count/ Allergy tracker UK
@andyh6278 wrote: Hi all this topic has been around before, but i cannot find any integrations for the UK. I would really like to have pollen count and flu information displayed on our Lovelace UI. we...
View ArticleSlider to call local network API
@burg93 wrote: Hey, I’m pretty new to using HA so bear with my limited knowledge please! I have my blinds hooked up to a DIY motor solution which is controlled via an onboard api on my local network....
View Article